Supplier sign in
Home
STAY INFORMED
Subscribe to our monthly newsletter.
Your email address will never be disclosed to any third party.
Read our privacy notice.

       

Categories

Contribute
Displays
Select a category
Displays
Controllers  
Displays
Search

Companies

Penko Engineering B.V.SCAIME S.A.S
SSB Wägetechnik GmbHZELO Konstruktions und Vertriebs GmbH
Do you want to list your company here?  Add company

Posts

Explosion-Proof vs. Intrinsically Safe Equipment There are two characteristic electronic safety standards: intrinsically safe and explosion-proof. Which one do you need?
Explosion-Proof vs. Intrinsically Safe Equipment
There are two characteristic electronic safety standards: intrinsically safe and explosion-proof. Which one do you need? In regard to electronic safety standards, there are two characteristics that are often referred to in manufacturing: Intrinsically safe and explosion-proof. Sometimes the term “explosion proof” is also used to describe the environment of operations and both means of protection, environment or equipment, are acceptable for safe manufacturing processes. Intrinsically Safe Intrinsically safety equipment combats hazards because it is incapable of causing sparks or combustion. This means that intrinsically safe equipment must limit electrical current, voltage and heat. This reduces the risk of explosion in hazardous and combustible environments such as distilleries, chemical plants, fuel refineries or textile manufacturers. Intrinsically safe equipment may be more critical in areas impacted by system breakdown, vapors and gases, combustible dust or a combination of all three. Explosion-Proof Utilizing explosion-proof or flame-proof equipment is a method of protection
30.04.2021  |  949x  |  Product news  | 
PLICSLED – The new switching status display module for point
PLICSLED – The new switching status display module for point
With the new display module PLICSLED, the switching status of a sensor can be read from afar, even in strong sunlight. The module is compatible with all sensors of the plics® family with relay output: VEGASWING series 60, VEGAVIB series 60, VEGAWAVE series 60, VEGACAP series 60 and VEGAMIP series 60. Since external wiring is unnecessary, the time needed for installation is reduced to a minimum. Power is supplied via the relay electronics. The second relay output is used to control the switching status display. Depending on the module version, the switching status is displayed in the colour combination red-green or yellow-green. PLICSLED is installed directly inside the plics® sensor housing, which gives it a high degree of protection from dust and water ingress.
17.11.2014  |  20848x  |  Product news  | 
New: Dosing-weighingterminal for zones 1/21 witth built-in filling- and dosing I/O
New: Dosing-weighingterminal for zones 1/21
witth built-in filling- and dosing I/O METTLER TOLEDO introduces the new weighingterminal for hazardous areas, the IND560x. Available in desk-, stand- and panelmounthousing. Suitable for analog and digital weighingplatforms and -loadcellsystems. The optional fill-application makes the termnial an excellent component for accurate and fast dosingsystems.
13.08.2009  |  9120x  |  Product news  | 
New ATEX weighingscale Compact and battery supplied
New ATEX weighingscale
Compact and battery supplied METTLER TOLEDO introduces a new weighingterminal for Ex-hazardous areas. The IND226x has a rugged, industrial design and approvals for use in Ex-zones 1/21. For optimal mobility, an optional battery-supply is available, enabling mains- independent weighing performance for maximal 70 hours. Specifications: Connectable platforms: Ex-approved platforms (min. 87 Ohm) Display functions : x10 , over/under check, MinWeigh® Ex: Gas: II 2 G Ex ib IIC T4; -10C…+40C / Dust: II2D Ex tD A21 IP 66 T60C W&M approved: 6000e OIML
22.02.2008  |  8071x  |  Product news  | 
New filling- and dosingterminal for hazardous areas ATEX approved solutions
New filling- and dosingterminal for hazardous areas
ATEX approved solutions The METTLER TOLEDO program for hazardous weighingsolutions has recently been extendedwith the filling- and dosingterminal ID7sx/DOS. It can be operated in hazardous areas in combination with a broad range of ATEX approved weighingplatforms and loadcells (weighmodules)
04.12.2003  |  7141x  |  Product news  | 
Do you have an item for this page?  Contribute
PORTALS
BulkSolids-Portal Schuettgut-Portal Recycling-Portal
Related
Bulkgids.nl
SIGN UP FOR OUR NEWSLETTER
Newsletter archive
Service and contact
ContactDisclaimerPrivacyAdvertising
FOLLOW US
Linked